Browse

Recovery of gold and other valuable metals from electronic scrap involves a complex metallurgical flow sheet and requires state- of-the-art recovery technologies that are available in large-scal e, integrated smelter-refinery opera tions. At the end of their use, electronic and other el ectrical product scrap offer an important recycling potential for the secondary supply of gold and silver into the market. With gold concentrations reaching 200-250 g/t for computer circuit boards, this scrap is an ‘urban mine’...

The enhanced oxidation of su lphide minerals by mini ng activities is a worldwide problem of significant environmental interest because of leading to the generation of Acid Mine Drainage (AMD). These waters e xhibit very different chemical and physical properties depending on their origin and the geochemical nature of the site of exploitation. Low pH, high concentration of sulphates and various heavy metals cause their deleterious effect on the environmen t. Treatment methods to address AMD are focused on neutrali...

Recycling is the method used to reduce the environmental impact of large volumes of materials, the sparing use of resources is another relevant factor here. The waste materials which occur in the foundry and st eel industry alongside the target products most be used elsewhere or returned to the foundry and steelmaking processes. The result will be that the need to dispose of material s will be greatly reduced , so alleviating the demand for landfill capacity. In addition, raw material depo sits will be conserved a...

The goal of a recycled paper or board manufacturer is to make a product that meets customersО„ specification and requirements. At the present utilization rate, using recycled fibres in commodity grades such as newsprint and packaging paper and board has not caused noticeable deterioration in product quality and performance. The expected increase in recovery rates of used pa per products will require a considerable consumption increase of recycled fibres in higher quality grades such as office paper and magazine pa...

The paper presents the main factories which determine the environment pollution at hot dip galvanization process of steel sheet and developing of recycling technologies of zinc by-product, with a view to recovering metal zinc or different sub- products, and returning them in the production cycle. By th e recycling of zinc by- products the prime material consumption is reduced and enviro nmental protection is improved. Industrial wastes generated in the hot dip galvanization pr ocess of steel sheet are: zinc ash, d...

In this paper we describe the analysis of costs associated with disposal of hazardous and common waste, in the construction company. Furthermore, we show how to implement Six Sigma methodology to reduce costs of waste disposal. On the specific example from practice there is shown the effectiveness of this approach in the management of waste in the practical conditions of a construction company.

Artova ophiolite complex is located along the North western and east margin in Yozgat (Turkey). The Mn-deposits in the Derbent an d Eymir areas are part of this ophiolite complex. These deposits, both banded and lenticular forms, are hosted by radiolarite and are generally overlying volcanics. Braunite, jacopsite, psilomelane and goethite are main constituents of the manganese ores in Eymir (Sorgun-Yo zgat) and manyetite, manganite, pyrolusite and goethite are main constituents of the manganese ores in Derbent (Ma...

A similar succession of Foliation Inflection/In tersection Axis trends preserved within porphyroblasts (FIAs) is present in two areas separated by 200 km along the Rocky Mountains. PreCambrian rock s in Central Colorado and Northern New Mexico were affected by deformation and metamorphism from approximately 1506 to 1370 Ma. A succession of five FIAs trending W-E, SSW-NNE, NNW-SSE, NW-SE and WSW-ENE has been distinguished in Central Colora do that have been dated at 1506В±15 Ma, 1467В±23 Ma, 1425В±18 Ma, not dated ...

The present paper is devoted to the results of long-term field observations of oil pollution transformation in sma ll watercourses of the Lower Don River basin (Russia), on the Atlantic coast of France and in the Strait of Kerch polluted by spilled oil. The investigations included visual assessment and sampling of oil slicks, water and sediment cores. The analysis of samples were carried out with the use of th in layer and column chromatography, optical and gravimetri c methods making possible to determine separat...

In conductive heat transfer mechanism daily (diurnal) temperature variations almost damp in a layer as deep as 1 m, and annual variation do it as deep as 18-21 m. In case of coincidence of periodic heating with flui d mass transfer (downward percolation of surface water from rivers), thickness of the layer with periodic temperature fluctuations increases significantly. This discovery with author`s priority registered August,19, 1964, was made by N.M. Frolov. We consider the research on temperature waves created in...

The aim of this paper consists in highlighting the feasible technical solution in a real situation, namely to achieve the consolid ation of the road accessing the monitoring block from Obrejii-of-CДѓpГўlna dam. As a consequence of the landslides occurred on the left flank, between the intersection with national road DN 67C and Podu Vacii point, at about 50 - 60 m downstream the dam, it was proposed the narrowing of the access road platform, to the surveillan ce and control block of the dam, on 20 - 30 m length. Ac...

Ever increasing industrialization has b een an important factor causing many environmental problems. Man made inputs asso ciated with industrial practices; mineral exploration, industrial processes and solid wa ste management contribute to heavy metal contamination of natural ecosystem. Nickel is one of the heavy metals that are present in industrial water from traces to very high quantity. Extraction of Ni 2+ from the effluents using flyash depends on various parameters such as pH, quantity of fly ash and sorptio...

Conducted research of processes of dry an d wet mechanoactivation of wolframite concentrate and structural modifications were determined. With a purpose of maximum transference of tungsten from obtained after-sintering mixtures into solution, investigation wa s conducted, conditions of hydro desalination were determined and technological regime of the process was developed.

Self-ignition processes are a serious probl em in brown coal mining and depositing. Infusions and following fires are frequent events in open pit brown coal mines with seams influenced with previous underg round mining, homogenisation and other deposits, and on stock-piles of power and heat stations and industrial plants combusting coals as well. The objectives of the project from the ALFA programme No. TA01020351 are presented in this article. The project solves a research, development, and verification of a comp...

This article is a summary of previous rese arch results focused on solution of rainwater use in urban areas. The research was focuse d on monitoring of quality and also quantity of caught rainwater. Based on rainwater qua lity monitoring the results were evaluated and compared with valid legi slation and some improvement s of rainwater to quality corresponding to drinking water were proposed. By the water treatment the aggression of rainwater was first solved, which was ev aluated on the basis of test according to...

Road structures construction and maintenance involves the use of large amounts of materials, including natural aggregates that occupies the largest share. On one hand the quality of natural aggregates, and other road ma terials, is decisive for the success of the technologies used in the road construction sector and on the other hand, the diversity, and number of the possibilities of purchasing and the number of producing units are more varied for natural a ggregates with possibilities to significantly influence t...

This paper represents results of measuring of sedimentary dust at two locations. One location is at SM where installed is old fa shioned technology for limestone processing. The other location is „Kota“ near Vareš, where installed is contemporary technology for limestone and spilite processing with application of BAT (the best available technique), and is a property of company „BBM Vareš“ d.o.o. from Vareš. Measurements confirmed that during limestone processing wh ere old fashioned technology is instal...

The article deals with brownfields which orig inated as a secondary result of different character of restructuring land used in the past in any EU country and time often accompanied by extreme burden on the individual components of the environment. Removal of the resulting environmental burden would contribute not only to improvement of the environment but also to further socio-economic development of the region in which the brownfield is located including primary, secondary and tertiary sectors of business enviro...

The open pit Veliki Krivelj is a copper mine which operates within RTB Bor Group in Serbia. In 1998 a combined haulage system involving the initial dump truck haulage, crusher, belt conveyor and a boom spreader for waste disposal was designed and installed in order to reduce the costs on overburden removal. The designed productivity of the system is 4 700 t/h and it will be fully operational in the next few weeks. Up to date it has been capable of achieving maximal 50% of this productivity because only one of two ...

This paper gives some information about risk management and its significance for financing project in mining industry. The projects in mini ng industry are very exacting for financial sources. By the obtaining of financial sources must be accepted kinds of financing. In the concrete mining company we were determining, which kind of financing is possible to use to finance mini ng projects with acceptance of risk. With the selection of the form of financing are conn ecting risks, that we are analyzing and we were pr...

The original method for the assessment of risk of geodynamic processes in mountain areas was developed. The proposed indices are as follows: relief structural stages, degree of tectonic break, stru ctural intersection nodes of faults, tectonic valleys, the intensity of slope processes, permafrost f eatures, and landscape differentiation of the territory. The geodynamic indices were estimated with factor maps of the GIS-project using the analysis of morphotectonic block structure, and the field geomorphological and...

The paper objective is to assess the social responsibility issues among the SMEs in Romania. We seek to find the main charac teristics of responsible citizenship among the SME sector and its internal and external drivers.

The contribution deals by the suggestion of new manufacturing technology for hand- made screw blade for wind-power plant. A wind turbine is a device that converts kinetic energy from the wind into electricity for distribution. Wind turbine blades are most often fabricated by hand using multiple layers of fi breglass cloth. The traditional method is for the sheets to be cut to shap e, laid down in a mould by hand, sprayed or rolled with resins, and finally cured. The automation of the manufacturing of hand-made pro...

The study includes the geochemical data of foraminifera in Pleistocene-Holocene aged marine sediments outcropping along the coasts of Gulf of Antalya and around the Belek, Kadriyeköy and Kumköy settlement places in the south of the Serik (eastern Antalya) in Turkey. The chemistry of benthic foraminifera tests can include records of seawater and provide data on environmental interpretation. For this purpose a total of 28 benthic forami nifera were selected from similar genus and species of benthic foraminifera an...

The Maastrichtian aged Dikmendede Formation in the Orhaniye (Kazan-Ankara) area formed in a deep-marine environment. The formation consists of alternating green, grey-coloured turbiditic conglomerate, sands tone, shale, claystone and marl. The unit has typical flysch features and has sediment ary structures such as thin/thick bedding, normal graded bedding, erosional surfaces, flut e casts, load structures, ball-and-pillow structures, bounce marks, slump structur es and numerous biogenic traces. The conglomerates ...

Sedimentary analysis was based on formati ons of inferior Molasse which belong to Burdigalian and Badenian, being performed in representative natu ral claddings from Prahova, Romanian area. Complete successions of Variegated Formation and Globigerina – bearing Tuffs and Marls Formation may be followed in V. Mare – Alunis and Slanic–Piatra Verde Quarry (Prahova). The Variegated Formation is mostly ruditic– arenitic at its base, grading into a silty–lutitic sequence at the top. It mainly consists of conglo...

The most recent glacial period span in the interval 110,000 to 10,000 years ago. Recent geomorphologic studies in the Eastern Thracian plane have shown significant change in the sedimentation rates since the Younger Driass (between 10,800 and 9500 BC), which may provide a new inside on the climatic evol ution of the region. It was found that all local rivers are in an aggradation phase, depositing up to 3 m thick mudstone deposits on top of a colder climate’s well-washed, coarse sandstones. The aggradation resul...

In this paper the results of sedimentological analysis of coal in 2010 at the lokality Petka (western coal basin Kostolac). Are presented variations of petrographic composition of coal matter (lithotypes, microlithotypes and macerals), mineral admixtures (clay, aleurite and marl) and locally occurring epigenetic mineralizations. The Kostolac Neogene Basin (Figure 1), cont aining three tick lignite beds of Pontian age[1] is one of important energetic resources of Serbia and is the bases for operating two lignite-fi...

The importance of understanding seismic waves and measurement waves has gravitated form the seismic prediction to training electromagnetic propagation. Seismic electromagnetic waves may be useful in shor t-term earthquake prediction. It was found our observation system is influenced by lightni ng as far away as about hundreds km in the VLF and LF range. It is found that the increase in the number of LF and VLF electromagnetic pulses before earthquakes were generated by lightning. Some researches show that there is...

The aim of the paper is to in form on the need to apply geological information in land use planning and other state administration spheres, such as building office services. The study was carried out with in the locality specified by a map sheet 15 44 07 in 1:10 000 scale, in the cadastral district of Petr vald, Orlova, Horni Such a in the north-east of the Czech Republic close to the Polish border. The subject of the study is an evaluation of geobarriers of rock workability, inundatio n area and radon index. A si...

The aim of this paper is to develop a methodology for predicting the potential of future drilling, not merely on average but more specifically as a function of the grades obtained in the drilling in Chadormalu Ir on ore deposit. In most cases additional samples are collected to reduce the overall unc ertainty on the estimation. To do this, the GET function method is used to find the bore hole locations that are more sensitive in reducing the local and global uncertainty than others. This function considers the Gra...

Aquaculture is a rapidly growing industry that is vital to supplying the increasing demand for food production worldwide. In recent decades, Aristichtys nobilis (Bighead carp) and Hypophthalmichthys molitrix (Silver carp) have been widely introduced into European waters for algal control and as a food source. This species are very sensitive to various environmental and physical stresses and thus more susceptible to bacterial invasions resulting in disease outbreak and mortality. The ma jority of bacterial fish pat...

Investment in the mine scope is one of the most risk able fields. In the new management skills, risk management is a ve ry important feature. During of the execution of a mine project, the variation of each effective factor can affect on the execution, production and efficiency, therefore a mining project ma nager must be knowledge about of any effective parameter such as Annual productivity, annual benefit, annual cost and exploitation time, in project The net present value (NPV) is one of the most important meth...

The paper deals with the verification of the possibility of using the froth separation to separate highly concentrated coarse-grained black coal slurry. For laboratory research samples of raw coal with a grain size fraction of 0,2 - 2 mm from the Paskov Mine were used. The achieved se paration results confirmed the ability of froth separation to separate coarse-grained highly concentrated sl urry. The coal slurry in concentrations of 332 kg.m -3, 400 kg.m-3, 500 kg.m -3, 600 kg m -3, 668 kg m-3 was successfully se...

In the world, over 18 million vehicles are rejected annually from operation. The spent catalysts are obtained from th e vehicles at the end of their life cycle as well as the vehicles which do not meet the prescribed st andards in the ECO test respected to the composition of exhaust gases. The basis of each catalyst is a ceramic monolith with deposited valuable platinum metals. The spent catalysts are solid waste and also the rich raw material for recovery of precious metals. The aim of this paper is a separation ...

Energetic theory of disintegration repres ents the starting point for the search for optimum of rock cutting, as it issues from the instantaneous advance rate of the indentor, specific cutting energy (am ount of energy used for cutting of a unit volume of rock) depending of applied thrust. Search for optimum on experimental drilling stand using the optimization met hods is impossible due to technological limitations (limited area for optimum search due to limited rock sample length, duration of experiment, possibl...

The current paper marks the early stage of the PhD thesis of the first author of the paper. The thesis includes partial creation of an educational repository system, which should become a highly flexible portal that gives a ccess to variety of educational resources. The simulation of the development of the repos itory system is the main topic of this paper. The human resources needed for the su ccessful end of the project are centric for the simulation which can be quite useful not only for developers of similar s...

Developed is software package for acoustic calculations, named SoundBG. Described program modules should be considered as a fi rst step in creating a sufficiently complete programming library for acous tic calculations, which will gradually replace the traditional graphics, tables and approximate formulas.

Solid waste management has become an environmental concern for many developing countries including Libya country. There have been several significant obstacles facing the city of Al-Abyar in dealing with th is issue including; limited documentation regarding generation, handling, management, and disposal of waste. In this paper, solid waste management status in the city of Al-Abyar has been investigated through an extensive survey carried out on selected p ublic and private comp anies. Solid waste management pract...

Sorkhe-Dizaj iron oxide - apatite deposit is located within the Cenozoic Tarom volcano- plutonic belt in southeast of Zanjan, northwest Iran. The oldest units at the Sorkhe-Dizaj area are of Eocene age including trachyte, trachyandesite and andesitic tuffs intruded by quartz-monzonite, monzonite and granite plutons of Upper Eocene-Oligocene. The syn- to post-orogenic island arc magmatism and th e plutonic rocks show characteristics of I- type granites. Mineralization in the area is divided into th ree main zones (...

Zinc is a widely applicable metal and therefore the different composition and form of zinc waste is generated. The most important waste material generated in production and processing of zinc is scrap metal of zinc and its alloys, as well as slag, dust and sludge from the production and processing of cat hode zinc and zinc alloys. In terms of processing technology, there are different app lied procedures depending on the type of raw material. The processing of waste zinc a nd its alloys is pyrome tallurgical and i...

This bachelor thesis is focused on speech synthesis of Czech language in frequency domain. The resulting software solution consis ts of the analyzer and synthesizer of selected elementary speech units. Speech synthesis is based on the LPC model. The analyzer analyzes an input phoneme unit in WAV format, divides it into microsegmens of length 20 ms and keeps the LPC coefficients, flag (voiced / unvoiced) and the residual prediction error signal. These data are then stored in the XML file. Further, this thesis deals...

The paper deals with verification of the sl udge stabilization from retention tanks by using modified cellulose fibers. Verifica tion of the method was implemented through laboratory tests and field test. Laboratory te st take place in VUHU a.s. Most and field test was performed at the quarry Ji Е™Г­, Sokolov coal company, a.s. legal successor. Stabilization took place in order to allow extr action of sludge from retention reservoirs. These reservoirs are build for longer time period and must be cleaned due mainta...

Public Enterprise Elektroprivre da Srbije (EPS - Electric Power Industry of Serbia), the dominant electricity producer in Serbia, is a 100% state-owned public company. The Kolubara Mining Basin (MB Kolubara) with its open cast mines is one of 11 subsidiaries of EPS. In accordance with the Serbian Energy Strategy by 2015, one of the EPS priorities is a modernization and improvement of the efficien cy of EPS' coal mining operations at the Kolubara basin and significantly improvement the quality and uniformity of the...

This paper aims to highlight the concerns about the waste management and at the same time highlighting its regional peculiarities. Municipal waste management methods in use today are related both to the waste that are being generated and collected, as well as waste that are generated and then collected . Collected waste are waste that are being generated and then collected by the sanita tion services. Waste uncollected is waste generated but not collected by sanitation services. The methods that are used, such as ...

Titanium is a biocompatible material used in dentistry as una lloyed (minimum purity 99.4%) and alloyed, the most widely used is TiAl6V4 despite some reservations about the releasing of Al and V ions, which can be accumulated in the tissues. To increase the surface contact between the implant and bone, facilitating osseointegration the implants are coated with titanium or ceramic mate rials leading to a ro ughness surface which creates conditions for bone growth, resulting a better anchoring between the implant an...

It is aimed here to perform electrical resistivity measurements to define ground differentiation especially for 10-20 meters depth. This research purposed to evaluate the groundwater condition around Selcuk Univers ity, Law Faculty building groups in Alaaddin Keykubat campus. After the electrical resistivity tests, ground resistivity graphics were drawn for further researches on buildings’ structural analyses. The results supplied several cross-sectional 2-D resistivity graphics which were used to understand the...

The paper presents research of the structure of the geomagnetic field in correlation with the neotectonic regionalization. The territo ry of the Republic of Macedonia, according to the neotectonic processes, is divided in three zones: Western - Macedonian zone which include Alpine orogeny and Pelagonian massif, Vardar zone and Eastern - Macedonian zone which is part of the old Paleozioc rock mass on the Balkan Peninsula. Anomalous geomagnetic field on the territory of the Republic of Macedonia is presented with re...

In the context of sustainable development the problem of water pollution has a greatest importance due to the necessity of ensuring a clean environment for the next generation. Water quality standards provide the framework of accepted water parameters: chemical, physical, microbiological, biochemical, radiological. The European standards show the sampling method and terminology accep ted for that in according with macro- regional environmental conditions. In the present conditions, a good standard of life for peop...

Unsustainable consumption and production pa tterns in the developed world have an increased generation of waste over many decades. One of the major environmental challenge is the enormous amount of waste generated from leather and footwear industries. The leather and footwear industr ies are diverse manufacturing sectors which employ a wide variety of materials to make products ranging from different types and styles of clothes and footwear. Over 40 di fferent materials can be used but leather represents the most ...